top of page

Low Water Pressure in Your LA Home? How to Find the Cause

Writer: Asher
Asher
1 hour ago
4 min read

A shower that dribbles, a kitchen faucet that sputters, a washing machine that takes forever to fill. Low water pressure is one of the most common problems Los Angeles homeowners call about, and in most cases you can narrow down the cause in about 15 minutes without any tools.

The trick is to notice where the pressure is low. One fixture, hot water only, or the whole house each point to a different problem, and knowing which one you have saves a lot of guessing.

The 5-minute version 1. Find the pattern. One faucet, hot only, or the whole house? 2. Check the valves. The main shut-off must be fully open, and so must the valve at the meter. 3. Clean the end of the faucet. Mineral buildup in an aerator or showerhead is the most common single-fixture cause. 4. Test the pressure. A reading under 40 psi at a hose bib means something is wrong in the house or at the street. 5. Whole-house drops need a plumber. A failing regulator, corroded pipes or a hidden leak are the usual causes.

1. Start with where the pressure is low

  • One faucet or showerhead. The problem is almost always at the fixture itself, either a clogged aerator or showerhead, or a partly closed shut-off valve under the sink.

  • Hot water only. Cold is strong and hot is weak? Look at the water heater, its shut-off valve and the hot lines. Sediment in the tank is a common cause. Our water heater repair team sees it often.

  • Every fixture in the house. That points to the main valve, the pressure regulator, corroded supply pipes or a leak before the water reaches your fixtures.

  • A sudden drop. Pressure that falls overnight is a different story from pressure that has faded for years. A sudden change often means a leak, a closed valve or a street-side issue.

2. Five checks you can do yourself

  1. Open every valve all the way. Check the main shut-off at the house and the valve at your meter. A valve that is only half open, sometimes after recent work on the street or in the house, is an easy fix.

  2. Ask a neighbor. If the house next door has weak pressure too, the cause is probably on the street side and your water provider is the one to call.

  3. Unscrew the aerator or showerhead. Soak it in white vinegar for an hour and rinse. Los Angeles water is hard, so the white crust you see is mineral buildup. Our guide to hard water in California explains why it keeps coming back.

  4. Look for a hidden leak. Turn everything off and watch your water meter. If it keeps moving, water is escaping somewhere. Here is how to check for a hidden leak in 10 minutes.

  5. Put a gauge on a hose bib. Screw an inexpensive pressure gauge onto the outdoor spigot nearest your meter, turn the water on fully and read the gauge once the needle stops. A normal reading is 45 to 60 psi, and anything under 40 psi is a problem worth fixing.

Thin stream of water running into a bathroom sink
A weak stream at one faucet is usually a clogged aerator. A weak stream everywhere is a bigger job.

3. What causes low pressure in the whole house

  • A failing pressure regulator. Many LA homes have a regulator near the main shut-off that keeps street pressure from overloading your pipes. When the diaphragm wears out, pressure can sag or swing between too low and too high.

  • Old galvanized or corroded pipe. Older Los Angeles homes often still have galvanized steel lines. The inside of the pipe slowly narrows with rust and scale until water has to squeeze through. See what rust in your pipes is telling you.

  • A leak. Water that escapes under the slab or in a wall never reaches your faucets. Our slab leak detection and repair finds it without tearing up the whole house.

  • A bad main line. A cracked, kinked or corroded line between the meter and the house loses pressure along the way. That is a job for home water line repair.

  • Old supply pipe that has reached the end. When repairs stop holding, copper repiping restores full flow. Our copper pipes pros and cons breakdown helps you decide.

Water meters and pressure gauges on supply pipes
Your meter and gauge readings tell you whether the problem is on the street side or inside the house.

4. High pressure is a problem too

If your gauge reads well above 60 psi, do not celebrate. Pressure that is too high wears out faucets, toilets and water heaters faster. When static pressure goes over 80 psi, the California Plumbing Code calls for a regulator that brings it back to 80 psi or less. Elevation changes across Los Angeles mean street pressure can vary a lot from one neighborhood to the next, so a reading is worth taking even when the water feels fine.

Water running from a faucet into a sink
Strong, steady flow at every fixture is the goal, not just the strongest flow you can get.
Call a plumber right away if your pressure drops suddenly and you also see wet spots on a wall or floor, hear water running with everything off, find a warm patch on the floor, or notice your meter spinning while no water is in use. Shut off the main valve while you wait. Brown water along with low pressure can point to corroded pipe and should be checked soon.

Want your water pressure checked before it gets worse?

Boss Plumbing provides plumbing and heating service across Los Angeles. If your pressure is low, uneven or too high, call us at (323) 464-4700 or contact us online. We test the pressure, find the cause and tell you what it takes to fix it. For other problems around the house, our plumbing repair service covers it.


 
 
 

Comments


© 2026 Boss Plumbing. All rights reserved. License #579704
936-0001.png
Family owned and operated for over 37 years. Your trusted Los Angeles plumbing experts for residential and commercial services.
  • 936-0026
  • 937-0007
  • 937-0008
  • 936-0028
Contact Us
826 Seward St, Los Angeles, CA 90038
bottom of page